CanyCom CM223 Betreibershandbuch

Read this manual completely before operating or maintaining this machine. Failure to follow safety precautions could result in serious injury or deat

Safety 1-1-Safety LabelsThe safety labels shown on the next page are attached to the machine. See the illustration below for the location and the illu

Safety-2-15321 5113 00015321 5115 00025321M-0101-020E5321 5118 00035305 5326 00055321 5116 00045321 5114 0006 3667 5063 0007

Safety 1-3-Safety MechanismsThis product is equipped with the following safety mechanisms.Engine can be started only when parking brake is in [ (

Safety-4-1This section contains safety precautions to follow when operating and maintaining the machine. Read and understand the precautions in this s

Safety 1-5- • Fuel is highly ammable. See Checking and Filling Fuel, page 17, for important safety information on handling fuel. • Always wear prot

Safety-6-1Operation • Do not operate the engine in a conned space where dangerous carbon monoxide fumes can accumulate. • Do not touch the engine,

Safety 1-7- • Always travel slowly and use extra caution when operating on unfamiliar terrain. Be alert when traveling on changing terrain. • Never op

Safety-8-1Driving on a Slope • Always follow proper procedures for driving on a slope as described in this manual. • Driving on a slope in a wrong man

Safety 1-9-Parking • Park the machine on a at, level and stable surface. Never park on a slope steeper than 10 degrees. Avoid parking on a slope

Safety-10-1Servicing • Do not service the machine when the engine is running. If it is absolutely necessary to run the engine while servicing, beware

http://www.canycom.co.jp/ Sales Headquarters TEL +81-(0)943-75-2195 FAX +81-(0)943-75-4396 Foreign Trade CenterTEL +81-(0)3-3552-6277 FAX +81-(0)3-355

-11-Controls and Components 2Name and Function of ControlsForwardFuel Filler CapSteering WheelCutting Blade Shield, LeftCutting Blade Shield, RightTai

Controls and Components-12-21 Main Switch . . . . . . . . . . . . Main switch is used to start or stop engine.2 Throttle Lever . . . . . . . . .

-13-Controls and Components 25 Brake Pedal . . . . . . . . . . . . Brake pedal is used to stop machine. When brake pedal is depressed, drive lever r

Controls and Components-14-217 Hour Meter . . . . . . . . . . . . . Hour meter indicates the cumulative total operating time of the machine in 0.1 ho

-15-Specications 3 · Use this product properly after understanding its specications thoroughly. Product SpecicationsModel and Type CMX222 CM223Mach

Specications-16-3No. Content Quantitiy Note1 Operator's Manual 1 This Manual2Operator's Manual for the Engine13 Engine Service Tool 1for Se

-17-Operation 4 • Keep re and spark away when handling fuel. • Always stop engine before refueling. • Do not ll beyond the limit (bottom of

Operation-18-4 • After adjusting steering wheel, try moving steering wheel back and forth and up and down to make sure it is securely locked in its po

-19-Operation 4 • Beware of pinch points when adjusting seating position. • After adjusting seat, try moving seat back and forth and up and down to ma

Operation-20-4Adjusting Seat Suspension (CM223 Only)1. Lift seat up2. Loosen lock nut.3. Turn adjust nut toward A direction to harden suspension.4.

Notice to Users and Maintenance Personnel • This machine can be very dangerous if the safety precautions in this manual and on the labels attach

-21-Operation 4Driving • Always start and run engine in a well ventilated place. • Always stay on seat when starting engine. Never attempt to start e

Operation-22-41. Make certain brake pedal is depressed and locked. If it is not, depress brake pedal and pull lock lever to lock it.2. Make sure cut

-23-Operation 44. Make certain drive lever is in [ (neutral)] position.5321M-0402-040EDrive Lever • Drive lever returns to [ (neutral)] w

Operation-24-4Driving • Do not operate drive pedal or drive lever when brake is locked with parking brake lock lever. It can wear out brake. • Al

-25-Operation 44. Depress brake pedal to release brake pedal lock.5. Depress gradually the forward or reverse side of drive pedal to move in the cor

Operation-26-45. Move drive lever gradually forward or backward to move in the corresponding direction.5321M-0402-140EDrive LeverDriving wi

-27-Operation 41. Gradually return drive pedal to slow down.2. Take foot off drive pedal. • Do not depress brake pedal when drive pedal is

Operation-28-4 • Always shift gears rmly. When transmission is not rmly shifted, it may jump out of gear, resulting in loss of control of machine.Sh

-29-Operation 4Shifting Between 2WD and AWD (CMX222 Only) • Always stop machine to shift between 2WD and AWD (all-wheel-drive) modes. Shifting gears w

Operation-30-4Locking Differential • Always stop machine to operate differential lock lever. Operating differential lock lever while machine is i

Warning Term Denition Indicates an imminently hazardous situation which will result in death or serious injury if the user does not follow the proced

-31-Operation 41. Stop machine.2. Move throttle lever toward [ (slow)] to slow engine speed. • Always park on a rm, level place. Never park on

Operation-32-45. Turn main switch to [ (off)] to stop engine. Remove ignition key.5323M-0402-210EMain Switch

-33-Operation 4Working1. Push lock button to unlock cutting height adjust lever.Inspecting Cutting Blade2. With lock button depressed, move cuttin

Operation-34-4Cutting HeightMemory Lever5321M-0403-030E1. Lower cutting height adjust lever.2. Turn up cutting height memory lever.3. Slide rod to

-35-Operation 4 • Never place any part of body under cutting blade shield.Cutting • Always wear protective footwear, long trousers, hardhat, safety

Operation-36-4 • When working in a dusty area, clean air cleaner element twice a day. Dirty air cleaner element results in poor starting, poor perform

-37-Operation 45321M-0403-070EAuxiliary TransmissionShift LeverCutting HeightAdjust Lever5321M-0403-020E4. Move cutting height adjust lever to a desi

Operation-38-45321M-0402-140EDrive Lever7. Move cutting rotary clutch lever to [OFF] to stop cutting blade.6. Drive machine forward to cut.5321M-040

-39-Maintenance 5Maintenance Schedule • Follow the scheduled maintenance as described below. Failure to do so may result in mechanical or property

Maintenance-40-5 • Perform a pre-startup inspection (PSI) before each use, a monthly inspection once a month, and a yearly inspection once a year. • S

Warranty and After-Sales ServiceCHIKUSUI CANYCOM, INC. guarantees this product, based on the terms of warranty. A copy of this warranty is reproduced

-41-Maintenance 5Item DescriptionScheduleNotePSIMonYearDrive TrainHSTHST shall perform normally..√ √ √Hydraulic uid shall be lled to a proper

Maintenance-42-5Item DescriptionScheduleNotePSIMonYear Cutting System CuttingSystemBelt tension shall be properly adjusted.√ √ √Page 66Belt shall be

-43-Maintenance 5List of Fluids and LubricantsItem Schedule Grade Cap.Fuel As needed. Automotive Unleaded Gasoline14.5 LEngine OilFillInspect daily. F

Maintenance-44-5Greasing PointsLocation Schedule Grade1 Center pivot, front axle Every 6 Months Chassis Grease2 Drive pedal pivot Every 6 Months Chass

-45-Maintenance 5Greasing Points (CM 223)Location Schedule Grade1 Center pivot, front axle Every 6 Months Chassis Grease2 Both ends pivot, front axle

Maintenance-46-5List of Consumables and SparesItem Part No. Schedule Qty.EngineOil Filter Cartridge 248-65801-00Inspect every 50 hours.Replace if defe

-47-Maintenance 5Item Part No. Schedule Qty.Cutting SystemBlade Set (Pink) Z3214212010 Replace if defective. 1Blade Set (Silver) Z3214206010 Replace i

Maintenance-48-51. Unfasten knob nut.Front CoverRemoving and Installing Body Panels • Cut or pinch hazard exists when removing or installing body pan

-49-Maintenance 51. Unfasten bolt.Side Covers5319M-0505-030EBolt2. Pull up cover to remove.5319M-0505-040ESide Cover1. Undo latches.2. Open engine

Maintenance-50-51. Unfasten 4 bolts.2. Remove upper rear cover.Upper Rear Cover5321M-0505-060EBoltsUpper Rear Cover1. Unfasten 2 bolts.2. Remove l

Contents1. Safety 1Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Safety Mechanisms . . . . . . . . . . . . . .

-51-Maintenance 51. Raise seat.2. Unfasten 2 knob nuts.5321M-0505-080ESeatKnob Nuts3. Raise seat bracket.Cutting Blade Shield5321M-0505-090ESeat Br

Maintenance-52-5EngineEngine Oil • Always stop engine and remove ignition key before servicing. • An engine that has been running is very hot

-53-Maintenance 55. Visually inspect oil level. Make sure oil level is between upper and lower limits. If it is below lower limit, add oil.6. Vi

Maintenance-54-5Air Cleaner • Clean air cleaner element daily. Dirty air cleaner element causes poor starting, reduces engine performance and shortens

-55-Maintenance 5Spark Plugs1. Open engine hood.2. Remove spark plug cap.3. Remove spark plug with included spark plug wrench.4. Follow the instru

Maintenance-56-5Drive Train • Stop engine when servicing drive train. • Allow machine to cool off before servicing. Engine and its ancillaries are ver

-57-Maintenance 5Transmission Oil1. Park machine on a level ground.2. Have an appropriate oil drain pan.3. Open engine hood.4. Remove transmission

Maintenance-58-5Front Knuckle Oil (CMX222 Only)1. Park machine on a level ground.2. Have an appropriate oil drain pan.3. Remove front knuckle oil d

-59-Maintenance 5HST (Hydrostatic Transmission) Fluid5321M-0508-060EFiller Cap1. Park machine on level ground.2. Open engine hood.3. Remove HST 

Maintenance-60-51. Open engine hood.2. Remove right side cover.3. Remove suction lter cartridge.4. Have a new suction lter cartridge. Coat its s

Driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Starting . . . . . . . . . . . . . . . . . . . . . . . . . .

-61-Maintenance 5Drive Belt1. Remove upper rear cover.2. Check V-belt tension. Inspect that the length A of spring is within the range of 135mm+/-3m

Maintenance-62-5 • Always keep brake adjusted for maximum performance. Improperly adjusted brakes may result in property damage, serious injury, o

-63-Maintenance 5Cutting SystemCutting Blades1. Open cutting blade shield.2. Visually inspect blades and bolts for wear and damage. If blades or b

Maintenance-64-5 • Torque for Nut B - M12: 44.1-53.9N•m (450-550kgf•cm).NOTE1. Open cutting blade shield.2. Hold blade with a strong stick

-65-Maintenance 5Blade Types • Wider end increases durability. • Can be used as free or xed (with optional bolts) knife.5321M-0509-040ESilver5319M

Maintenance-66-5Cutting Rotary Drive Belt • Adjust belt tension properly. Inproperly tensioned belt may reduce performance and its service life.1. Re

-67-Maintenance 5Cutting Rotary Brake • Never place any part of body under cutting blade shield when cutting blade is rotating. • Do not allow bystand

Maintenance-68-55321M-0509-060EAdjust NutTurn BuckleSpringBC1. Remove upper and lower rear covers.2. Adjust the length B of spring with adjust nut s

-69-Maintenance 5Electrical SystemBattery • Never charge battery when the uid level is below "lower level" line. Charging battery with insu

Maintenance-70-51. Remove front cover.2. Remove two bolts and remove plate.1. Park machine on level ground.2. Remove front cover.Inspecting5321M-0

Removing and Installing Body Panels . . . . . . . . . . . . . . 48Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

-71-Maintenance 51. Remove front cover.2. Remove battery from machine.3. Follow instructions in battery charger user's manual to charge batter

Maintenance-72-5Light Bulbs1. Remove front cover.2. Remove 2 bolts to remove light unit. • When light bulb is burnt out, replace it with a new bulb.

-73-Maintenance 53. Remove rubber boot.1. Remove upper rear cover.2. Remove 2 screws to remove lens.Lens5321M-0510-060ETail LampLight Bulb5321M-051

Maintenance-74-5After Use CareCutting System • Never place any part of body under cutting blade shield when cutting blade is rotating. • Do not allow

-75-Maintenance 5After Normal Use1. Clean machine; wash off dirt, mud, and remove grass and other foreign materials after use.2. If machine is to be

Maintenance-76-5 • Do not wash engine or control panel with running water; water may enter inside and cause rust or damage. • Clean machine after use;

-77-Maintenance 5Storage1. Park machine.2. Clean machine; wash off dirt, mud, and remove grass and other foreign materials after use.3. Check machi

Troubleshooting-78-6Troubleshooting • If any malfunction or abnormal condition is found, immediately stop using the machine and take an approp

-79-Troubleshooting6Area Malfunction Possible Cause Corrective Measure Ref.EnginePoor power or accelerationBad fuel →Change fuel.Insufcient intake ai

Troubleshooting-80-6Area Malfunction Possible Cause Corrective Measure Ref.Drive TrainMachine does not move when drive lever or pedal is operated.Insu

WarrantyWarranty Certicate is attached at the end of this manual.* Have the warranty certicate signed after you have received and fully understood t

-81-Troubleshooting6Area Malfunction Possible Cause Corrective Measure Ref.Electrical SystemHead lamp or rear lamp does not illuminate properly.Blown

Troubleshooting-82-6Area Malfunction Possible Cause Corrective Measure Ref.Cutting SystemCutting blade cuts into ground.Cutting height is too low.→Rai

-83-Transporting7 • Park transporter (truck) on a level ground. Always use chocks to secure wheels. • Do not allow bystandars to come clo

Transporting-84-7Hoisting1. Lift seat.2. Attach hoisting slings to 2 lift hooks and hoist machine.5321M-0702-010EHooks • Licence or certication

ModelEngineLwAType Type Speed rpmCMX222, CM223 Robin EH65DS 2900 rpm 96 dB (A)NOISE LEVEL evaluated based on factory standard.NOISE LEVELModelEngineRa